P4MM4 – read user manual online or download in PDF format. Pages in total: Biostar | P4MM4 | Owner’s Manual | Biostar P4MM4 Owner’s Manual The content of this user’s manual is subject to be changed without notice and we . P4MM4 VIA P4M gaming motherboard features-Socket ;Supports Intel Pentium 4/Celeron D/Celeron Processor;Supports FSB /MHz;Support.

Author: Zuktilar Samuro
Country: Chad
Language: English (Spanish)
Genre: Art
Published (Last): 10 May 2009
Pages: 424
PDF File Size: 17.24 Mb
ePub File Size: 15.8 Mb
ISBN: 564-2-72233-260-8
Downloads: 52032
Price: Free* [*Free Regsitration Required]
Uploader: Keshicage

Connect the fan cable to the connector while matching the black wire bipstar pin 1. Enabled Virus protection is activated. State after power on. All the CMOS data will be loaded as defaults setting. When connecting with wires onto connectors, please note that the red wire is the positive and should be connected to pin 2, and the black wire is Ground and should be connected to GND. This node records which resources bioztar assigned to it. Page 31 P4MM4 Note: Disabled defaultEnabled.

Make a bootable floppy disk. Half-duplex mode permits transmission in one direction only at a time.

When enabled, the typematic rate and typematic delay can be configured. Remove the power cord from power supply for seconds. If the following message is shown after boot-up the system, it means the BIOS contents are corrupted. Off Numpad is arrow keys. Let user select a restoring way if system need to do a fail-safe reboot.

P4MM4 Solution Make sure power cable is securely plugged in. This completes the installation. TM2 Bus Ratio This option represents the frequency bus ratio of the throttled performance state that will be initiated when the on-diesensor goes from not hot to hot.


Biostar P4M80-M4 Owner’s Manual

These limits are designed to provide reasonable protection against harmful interference in a residential installation. Make sure power cable is securely plugged in. All hard disks are capable of breaking down at any time. In this panel, you can decide to increase CPU core voltage and Memory voltage or not.


When not disabled, each of the ranges is from 1 min. The information will be refreshed every 1 second.

The first hard drive should always be connected to IDE1. The user information of peripherals that need to use this area of system memory usually2 discussed their memory requirements. The fan cable and connector may be different according to the fan manufacturer. System only boots from optical drive. A password is required for the system to boot and is also required to access the Setup Utility.

Typematic Delay Msec Sets the delay time after the key is held down before it begins to repeat the keystroke. Half defaultFull. On defaultoff. However, this function is strongly recommended not to use. There are four options of Power Management, janual of which have fixed mode settings Min.

You will need to disable this feature if you add a higher performance controller. The kanual table provides more detail about how to navigate in the Setup program by using the keyboard. By pressing ‘print’ maunal you will print only current page. CPU fan is rotated normally. The vendor makes no representations or warranties with respect to the contents here and specially disclaims any implied warranties of merchantability or fitness for any purpose. This action will boot-up the system according to FSB of the processor.

This connector supports the provided floppy drive ribbon cables. Pull the lever sideways away from the socket and then raise the lever up to a degree angle. Hold the CPU down firmly, and then close the lever biosatr complete the installation.

  BS EN 50086 PDF

On default Numpad is number keys. In this panel, you can get model name and detail information in hints of all the chipset that are related to overclocking. There is no guarantee that interference will not occur in a particular installation. If install biostag FDC or the system has no floppy drive, select Disabled in this field. DPMS Initial display power management signaling.

Biostar P4MM4 | P4MM4 user’s manual – Page 15

Enabled default Enable cache. Overclock Panel Click the Overclock button in Main Panel, the button will be highlighted and the Overclock Panel will slide out to left as the following figure. TM2 Bus VID This option represents the voltage of the throttled performance state that will be initiated when the on-diesensor goes from not hot to hot.

Some graphic controllers which are not VGA compatible take the output from a VGA controller and map it to their display as a way to provide boot information and VGA compatibility. Onboard Serial P4m8-m4 2 Select an address and corresponding interrupt for the first and second serial ports The Choices: Hardware Installation Step 3: Page 27 P4MM4 3.

Don’t have an account? All the brand and product names are trademarks of their respective companies.