2. C C Product. Submersible pump for pumping clean water, surface water and waste water containing solids or long-fibred material. Denomination. Dataplate. rpm. Max 40°C. YSER/Y//V. 26/51A. kWhp. Date: Flygt CS MT. Use our handy online form to submit details on your existing Flygt pump to get a Flygt C Submersible Pumps Range Flygt C LT Submersible.

Author: Vojas Mazuramar
Country: Guinea
Language: English (Spanish)
Genre: Finance
Published (Last): 1 May 2005
Pages: 226
PDF File Size: 18.94 Mb
ePub File Size: 15.2 Mb
ISBN: 154-7-22371-939-1
Downloads: 53419
Price: Free* [*Free Regsitration Required]
Uploader: Shale

Seek medical attention, if required.

Product specifications | Flygt 3152 – Alaska Pump and Supply

Mount the suction cover: The impeller wear ring 1. Replace the valves, if necessary. The use of other parts can invalidate any claims for warranty or compensation.

Tightening torque, see Torque values page 32 vlygt. It is recommended that they are connected to 24 V over separate fuses to protect other automatic equipment. Please, check the surface intended for the wear ring that it is clean, before you are mounting flhgt new wear ring. Not applicable for PL-version.

Knock off the impeller wear ring from the impeller. The unit is frost-proof while operating or immersed in liquid, but the impeller and the shaft seal may freeze if the unit is raised in a temperature below freezing. The impeller is stuck. Connection to power Check that the connections are properly tightened. Support straps are required for deep installations. If the unit is stored more than 6 months, rotate the shaft every other month to prevent the seals from sticking together.

When the pump is connected to the public power supply, it may cause flickering of incandescent lamps when started.


Flygt – Alaska Pump and Supply |

Lay the drive unit on its side. Unscrew the oil plug.

For more information, please contact your Xylem representative. Service item Action Support and main bearing Replace the bearings with new bearings.

Periodical inspection To prevent operational interruptions and machine breakdown. Make sure that any thermal contacts incorporated in the pump are properly connected to the terminal board. This is an example of a product code, and an explanation of its parts.

Flygt Installation, Operation, and Maintenance Manual 49 Troubleshooting If the problem persists, refer to the Flygt Service Guide on the web or contact the local Xylem service shop.

Use a level or a plumb line. LL Replace the wear ring in the pump housing, diffuser ring, or suction cover Figure Always follow the limits given in Application limits page When installing or maintaining explosion-proof pumps, follow these guidelines: Use an insulation tester.

These requirements and instructions are for Z-installations that comply to the dimensional drawing. Temperature class Maximum ambient temperature Figure 3: The correct direction of impeller rotation is clockwise when you look at the pump from above.

Conduct insulation test phase to ground. Check the condition of the lifting handle. Flygt Installation, Operation, and Maintenance Manual 9 Transportation and Storage Lifting equipment The lifting equipment must fulfill the following requirements: Major overhaul To secure a long operating lifetime for the product.

Flygt 3000 Series / C Submersible Pumps

Failure to do so could result in death or serious injury. This conversion is done on the terminal board. Spare parts Xylem guarantees that spare parts will be available for 15 years after the manufacture of this product has 31552 discontinued.

Developing new technologies that will improve the way water is used, conserved, and re-used in the future is central to our work. The screened cable is necessary to fulfill European CE requirements. You must connect an additional earth- ground- fault protection device to the earthed grounded connectors if persons are likely to come into physical contact with the pump or pumped liquids.


Up to 12, hours or 3 year, whichever comes first. Flygt Installation, Operation, and Maintenance Manual Maintenance Major overhaul For a major overhaul, take this action in addition to the tasks listed under Inspection.

Check the control circuit and functions. Install the impeller and the wear protections For the HS-version, also install the wear protections. Intended use The product is intended for moving waste water, sludge, raw and clean water.

All non-English instructions are translations of the original instruction. The impeller is frozen Thaw the impeller by immersing the unit in liquid.

Drain all liquid, if any. The correct distance should be 0. If the outer sheath of the cable is foygt, then replace the cable.

If the flyg exceeds this value, for example when the control circuit is tested, the thermistors 3125 be destroyed. Install with P-installation In the P-installation, the pump is installed on a stationary discharge connection, and operates either completely or partially submerged in the pumped liquid.

Flygt Installation, Operation, and Maintenance Manual 11 Product Description Parts 7 6 4 3 2 5 1 12 Positio Part n Description 1 Impeller A wide range of impellers are available for different applications and capacities.