Together, EIA and JESDA detail the ESD requirements from the earliest steps in the assembly process to the final packing, shipping, and handling of. JEDEC. STANDARD. Requirements for Handling Electrostatic-Discharge- Sensitive (ESDS) Devices JESDA (Revision of EIA). DECEMBER charging up to dangerous levels (> 1kV) (JEDEC specification JESDA). Verify that machines and microscopes are properly grounded per JESDA.
|Published (Last):||4 July 2013|
|PDF File Size:||2.13 Mb|
|ePub File Size:||20.49 Mb|
|Price:||Free* [*Free Regsitration Required]|
A designated connection, location, or assembly used on an ESD protective material or device that is intended to accommodate electrical connection from the device to ESD ground.
When the supplier’s original packing materials and containers are noncompliant to this standard, jesd652 ESDS devices shall be rejected and returned in the original materials and containers. A packaging system that provides electrostatic protection and limits triboelectric charging to levels that do not result in device damage. Electrical charge at rest. A table top or other surface on which to work that has a resistance to ground of less than ohms ground: The ionizer shall be aimed at the devices and operator’s hands rather than at the operator.
Recommended Weekly a ESD protected workstation.
All ESDS devices shall be removed from the worksurface while making these measurements. Static Generating Sources and Charged Surfaces 5. NOTE — Surface resistance is expressed in ohms.
REQUIREMENTS FOR HANDLING ELECTROSTATIC-DISCHARGE-SENSITIVE (ESDS) DEVICES
NOTE — A material’s antistatic property is not necessarily correlatable with its resistivity or resistance. A work position with materials and equipment that limit electrostatic potential. The ESD caution label on the package may be provided by a preprinted marking on the package or its sealing tape.
Monochromatic reproduction mesd625 any color that contrasts with the background may be used. The required and recommended ESD item checks are listed in table 2. The caution label shall be legible to normal vision at a distance of three feet. The intent of this document jessd625 for users to incorporate these minimal requirements into their ESD control program to provide a consistent ESD protection level for their products.
A typical grounding system for an ESD protected workstation is illustrated in figure 1. When a floor grounding device e. This document is copyrighted by the Electronic Industries Alliance and may not be reproduced without permission.
When more than one ESD worksurface is used at a workstation, each surface shall be individually connected to the ESD ground. A material that has a surface resistivity less than 1x ohms per square or a volume resistivity less than 1x ohm centimeter. NOTE — A conductive material is not necessarily antistatic.
Otherwise, the attribute fail must be recorded. The dc voltage divided by the current passing between two electrodes of specified configuration that contact the same side of a insulative material or item. NOTE — The requirements of this standard are not imposed prior to probe. No claims to be in conformance with this standard may be made unless all requirements stated in the standard are met. NOTE — Topically treated tubes, trays, magazines and carriers tend to lose their static protective hesd625 with use and should be evaluated periodically for acceptable performance.
ESD Protective Worksurface 2. Equipment ground is the electrical ground green wire at receptacles that have been tested to and meet the requirements of NFPA or local equivalent. The transfer of electrostatic charge between bodies or surfaces that are at different electrostatic potentials. NOTE 1 Volume resistivity is generally expressed in ohm kesd625.
Jesr625 splices should be crimped or soldered. When both equipment and earth grounds are used at the same ESD protective workstation they shall be bonded together at some point in the ground system.
By downloading this file the individual agrees not to charge or jwsd625 the resulting material. However a lower value may be used if local safety requirements can still be met. Its value shall be within the limits specified in table 2, 1.
REQUIREMENTS FOR HANDLING ELECTROSTATIC-DISCHARGE-SENSITIVE (ESDS) DEVICES | JEDEC
Where both grounds are used, hesd625 shall be connected bonded together. Corrective actions resulting from monitor alarms shall be documented. The lowest level of ESD that produces changes in device characteristics such that the device fails to meet its specified characteristics. Referring to the property of material that inhibits triboelectric charging. The requirements within this standard were derived from existing industry standards, specifications, test methods, and input from various industry reviews.
JESDA ESD Handling Dec, _图文_百度文库
Prior to probe, the manufacturer should take appropriate ESD precautions to minimize damage to devices. NOTE — The electrical charge is due to the transfer of electrons within a body polarization or from one body to another. A short jfsd625 of electrostatic.
The generation of electrostatic charges when jesd65 pieces of material in intimate contact are separated where one or both is an insulator. When R2 or R3 are used, the resistor values shall be as recommended by the ESD protective equipment manufacturer.
The point, electrodes, bus bar, metal strips, or other system of conductors that form a path from a statically charged person or object to ground. A source of charged air molecules ions. Those with mid-to-lower resistance values provide shorter charge dissipation times.